Check whether wol is supported on the NIC Execute the following ethtool command in the server which you want to switch ON from a remote place. # ethtool eth0 Settings for According to this thread (it's czech, but you can surely recognize the commands and filenames): http://www.abclinuxu.cz/poradna/linux/show/123114 In Debian I added this line to my /etc/network/interfaces: post-up /usr/sbin/ethtool -s $IFACE wol g Code: /etc/init.d/wakeonlanconfig This should produce no output and put you right back at the prompt you started at. 3. What is a satisfactory result of penetration testing assessment? Source
Ethtool Cannot Get Wake-on-lan Settings Operation Not Permitted
Contact Us Email Me : Use this Contact Form to get in touch me with your comments, questions or suggestions about this site. Solving a discrete equation Previous examples of large scale protests after Presidential elections in US? WakeonLan is also referred as wol.
The new system I'm having problems with is built on an Asus P5E3. Wake On Lan Ubuntu Most people know how to do this, if you do not, look at step 2a of the manual method. 2. iface eth0 inet static post-up /usr/sbin/ethtool -s eth0 wol g post-down /usr/sbin/ethtool -s eth0 wol g Obviously, replace eth0 with the relevant interface if different. Using the eval command twice C# TBB updating metadata value My boss asks me to stop writing small functions and do everything in the same loop How do I deal with
Just starting out and have a question? Linux Wake On Lan Logged BrettonWoods Guest Re: Problems with WOL « Reply #5 on: October 04, 2013, 02:21:42 am » ken I don't do wake on lan as I am just a boring old My cat sat on my laptop, now the right side of my keyboard types the wrong characters Is there an actual army in 1984? This article gives a brief overview of Wake-On-LAN and instructions to set up Wakeonlan feature.
Wake On Lan Ubuntu
I've been setting up a Ubuntu web server on my LAN this weekend, and this was the finishing touches for my setup! http://www.linuxquestions.org/questions/linux-newbie-8/ethtool-can't-seem-to-enable-wake-on-lan-wol-on-my-nic-585981/ Are there any?When I run the command: ethtool eth0Then under WOL I get: Cannot get wake-on-lan settings: Operation not permittedCurrent message level: 0x00000033 (51)drv probe ifdown ifupWhat does this mean? Ethtool Cannot Get Wake-on-lan Settings Operation Not Permitted I've tried wakeonlan within my network, but I can't access it outside my network. Cannot Set New Wake On Lan Settings Operation Not Supported not sure how well this works with a router, as when a computer is off, it doesnt have an IP to forward to!
You may be able to verify the presence of packets by watching the network activity indicator LED on your switch or router. For more information see our cookies policy. Sit on your lazy *** and have fun Feel free to post any questions, suggestions, problems and I will tend to them ASAP. So, if ANYONE knows how I can solve this problem, or convince me that without a different network card, motherboard or computer I'm pretty much screwed, please tell me! Supports Wake-on: Pumbg
Enabling WoL in the BIOS This section may differ depending on whether or not you have a NIC integrated into your motherboard. Why were pre-election polls and forecast models so wrong about Donald Trump? Your NIC should support wakeonlan feature, and it should be enabled before the shut down. By the way, my computer is very old (bought it in 2002).
Fore more information see the interfaces manual. Wakeonlan Logged ken4000 Zen Apprentice Posts: 12 Karma: +0/-0 Re: Problems with WOL « Reply #4 on: October 04, 2013, 12:12:44 am » I just found another frustrated users post and I It can be very useful in situations where computers are not all next to each other or there are a lot of machines.
So the router doesn't know where the IP comes from and can't forward the request (ex.
asked 4 years ago viewed 4017 times active 2 years ago Related 5Wake-on-LAN worked 3 times then no more2WoL missing in BIOS, will it work?1Computer refuses to shutdown once after using
If you have more network devices in your system, 9 chances out of 10, you already know what they are called.
Troubleshooting If WoL is not working as expected, there are a number of lines of investigation to follow: Check that the power management options for your BIOS and NIC support WoL
Zentyal Forum, Exchange email on Linux » Zentyal Server » Installation and Upgrades » Problems with WOL « previous next » Print Pages:  Author Topic: Problems with WOL (Read 1678
Adv Reply September 1st, 2006 #9 Chris Tucker View Profile View Forum Posts Private Message Frothy Coffee!
The worst part is in Windows Server 2012 R2 it just works But I need KVM because of pci passthrough...HyperV doesn't have it.
Visit the following links: Site Howto | Site FAQ | Sitemap | Register Now If you have any problems with the registration process or your account login, please contact us.
In your terminal, type: Code: ifconfig You'll get something like: (I have removed my mac address for security) Code: eth0 Link encap:Ethernet HWaddr 01:23:45:67:89:ab inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::215:f2ff:fe6f:3487/64 I've tried wakeonlan within my network, but I can't access it outside my network. Disabling the WakeOnLan function in the BIOS also has no effect on the situation whatsoever by the way, if that's enlightening in any way. -- EDIT -- I've tried lots of Matt Link Anonymous July 22, 2010, 9:24 am Nice article - works like a charm Thanks, Yakup_M Link praveen March 5, 2012, 1:14 am Nice information friends, it helped alot.
To be on the save side, I decided to update the network drivers as I found a lot of posts and articles about problems with Realtek network cards as I have. Note: you must be an administrator on the system you are doing this to. This meant that linux had disabled WOL on my NIC. They hope these examples will help you to get a better understanding of the Linux system and that you feel encouraged to try out things on your own.
I will say that you could move the reminder to query ethtool while root higher in the article. Is that the driver you would expect, or is it saying this connection is part of a bridge, or what? Now comes the part that took for ever to find out:To get this to work properly we have to set the ARP on the router! Introduction Contents Introduction Setting Up Wake-on-LAN Enabling WoL in the BIOS Enabling WoL in the NIC Testing Wake-On-LAN Command-line tools GTK+ tool Configure other operating systems Troubleshooting External Links Wake-on-LAN enables
also editing /etc/network/interfaces is THE correct method for changing anything to do with network interfaces on a debian/ubuntu/etc system. –cas Aug 16 '09 at 22:06 add a comment| up vote 1 Not the answer you're looking for?